![quarts 17 linux usb blaster drivers quarts 17 linux usb blaster drivers](https://www.basic4mcu.com/data/file/h14/3660040649_cnr0oS2Z_driver.png)
- QUARTS 17 LINUX USB BLASTER DRIVERS DRIVER
- QUARTS 17 LINUX USB BLASTER DRIVERS PRO
- QUARTS 17 LINUX USB BLASTER DRIVERS WINDOWS 7
Quartus tool version - Quartus Prime Pro 16.1.0 Any help to fix this will be very helpful. I'm getting following error when I try to Synthesize my design. Maybe I misunderstand either VHDL or Quartus error message ( humbly thinking altera could make the message more clear).Īnyway, please help and your help is appreciated in advance. Since it should be very simple and straight forward, seems Quarts doesn't like me to use inout pin the feed a internal logic cell, but the bidir has to be supported because it's one of fundamental design units. Can't figure out why? Is it because some new development of VHDL I'm not aware or just the Quartus' interpretation? Searched around and tried a few methods but never solve it. When I tried to compile it, I got these error message "Error (13066): Illegal directional connection from the pin "GPIO_0" to the node "iBusData_IN" for all 8 bits. Signal FT_DataBus, iBusData_IN,iBusData_OUT, iData : STD_LOGIC_VECTOR (7 DOWNTO 0) -Databus and its derivatives Signal nRXF, nTXE, nWR, nRD, nOE: STD_LOGIC - FT2232H interface signals Signal fast_clk, FT2232_clk: STD_LOGIC -PLL clock and FT2232H Sync FIFO mode clock
![quarts 17 linux usb blaster drivers quarts 17 linux usb blaster drivers](https://community.intel.com/cipcp26785/attachments/cipcp26785/quartus-prime-software/35588/1/tools_programmer.jpg)
![quarts 17 linux usb blaster drivers quarts 17 linux usb blaster drivers](https://i.ebayimg.com/images/g/prMAAOSw7NJgWLsb/s-l640.jpg)
Use altera.altera_primitives_components.all use IEEE.STD_LOGIC_UNSIGNED.all - for some old compiler
QUARTS 17 LINUX USB BLASTER DRIVERS DRIVER
Running the JTAG Chain Debugger gives the following error messages:Įrror: TDI connection to the first detected device UNKNOWN_NO_JTAG_ID might be shorted to GNDĮrror: The TCK and TMS conections to the device before the first detected device UNKNOWN_NO_JTAG_ID might have a problemīoth systems use the same device driver (2.12.0.0) for the Altera USB-Blaster, and I experience exactly the same problem with a Terasic USB-Blaster.ĭoes anyone have an idea what may be causing this? Is this a Windows 10 or a VMware problem? Programming the same target board with the same programmer works perfectly from my desktop PC.Ī logic analyzer shows identical signal patterns on the JTAG interface. When I try to program the device with the Quartus programmer, I get the following error messages: With this setup, everything works fine as well, except programming. In order to be able to program and debug at the installation location, I have installed the development system on Windows 10 64-bit running under VMware Fusion on a MacBook Pro.
QUARTS 17 LINUX USB BLASTER DRIVERS WINDOWS 7
I use Quartus Prime version 16.1.0 on a desktop Windows 7 64-bit machine and use a USB Blaster rev. I am currently working on a project with a Cyclone IV E. My raw file is 32-bit, mono, format=raw, and 48K sampling. I'm trying to get audio file from project file and to play through the speaker with monitor program.īut it is not play correctly, but sounds like radio signaling sound. Volatile int *audio_ptr = (int *) AUDIO_SUBSYSTEM_AUDIO_BASE // audio port addressįILE * fpi1 = fopen("01_explosion.raw", "rb") // get file at project fileįread((void*)left_buffer,172000,sizeof(float),fpi1 ) // read file and store to left_buf, file size 172KB Volatile int * audio_ptr = (int *) AUDIO_SUBSYSTEM_AUDIO_BASE // audio port address #define AUDIO_SUBSYSTEM_AUDIO_BASE 0xFF203040 Could i ask you about Audio port operation?